Saturday, November 21, 2026 Sign in
Question · Rural Property · Nov 19, 20265-minute read

My BC Well Pump Was Replaced. Do I Need Another Water Test?

Yes, plan on one. The Province’s water well disinfection guide says to sample one week after the well is chlorinated, to retest a month after disinfection, and not to drink the water without boiling it until results show it is safe.

Home Farm

Yes, plan on one. The Province’s well disinfection guide says to sample one week after the well is chlorinated, to retest a month after disinfection, and not to drink the water without boiling it until results show it is safe.

Pulling a pump opens the well. New drop pipe, cable, and tools go down the bore, and hauling the old assembly up scrapes iron deposit and biofilm off the inside of the casing. That is why BC’s Groundwater Protection Regulation requires the installer to disinfect the well before leaving—and why having pressure back at the tap does not settle the question of the water.

What the Installer Must Do Under BC Law

Section numbers are the Groundwater Protection Regulation’s unless the line says otherwise. Each duty falls on the person responsible for installing the pump.

  • Registration: The Province says installing a pump in a well “is a restricted activity in B.C.” and “in most cases may only be performed by a registered well pump installer.”

    A registered well pump installer or registered well driller carries a provincial identification card as proof of qualification (section 13). Ask to see it: the Water Sustainability Act says they must show it, when asked, to the person who hired them (section 51 of the Act).
  • Casing: The pump goes in without damaging or moving the casing in a way that keeps foreign matter out of the well (section 44).
  • Backflow: A well with a permanent pump—one meant to stay in for more than 90 days—must have a check valve or other device that stops water from flowing back into the well (section 47).
  • Surface seal: If the work impairs the surface seal around the outside of the casing at ground level, the installer repairs or replaces it. If the well has no surface seal and the work opens a visible gap around the casing, the installer must seal that gap (section 48).
  • Wellhead: If the work required altering the wellhead, it must still meet the regulation afterward (section 49).
  • Pitless adapter: If a pitless adapter was installed, replaced, or repaired, its connection through the casing must be watertight (section 45).
  • Lubricants and solvents: Any lubricant or solvent used in the work must be non-toxic (section 50).
  • Disinfection: After installing a permanent pump or removing a temporary one in a water supply well, the installer must disinfect the groundwater in the well (section 52).

Two more rules sit outside the regulation’s pump sections. First, the Province’s guide on installing a well pump lists putting the well cap and cover firmly back in place when the job is done. Second, Technical Safety BC requires an electrical permit before regulated wiring starts—unless an exemption or emergency rule applies—and the wiring must be done by someone authorized to do it. Ask who wired the pump and whether a permit was pulled.

Testing Afterward

This part is public health guidance rather than a section of the regulation. HealthLink BC lists well pump installation, maintenance, or repair among the times a well should be disinfected, and Health Canada says to test after repairs or maintenance to a well or its equipment.

The Province’s disinfection brochure sets the schedule for a bacteriological test (total coliforms and E. coli): collect the first sample one week after chlorination (once all chlorine has been flushed from the system), retest one month after disinfection, and boil drinking water until the lab results come back clear.

If your well supplies two or more connections, HealthLink BC notes that you are a water supplier under the Drinking Water Protection Act: call your regional health authority about your testing requirements.

A lab result only tells you about the water on the day it went into the bottle, and HealthLink BC notes that many harmful contaminants cannot be tasted, seen, or smelled. Use the sterile sample bottles provided by an accredited British Columbia lab, and follow their collection and drop-off instructions exactly.

The Note

When a submersible pump dies, nobody is considering water chemistry—you just want the toilets to flush before dinner. The service truck pulls in, winches up a hundred feet of wet poly pipe, splices a new pump on, drops it back down, dumps chlorine through the top of the casing, and heads to the next call. In that rush, the crew almost always misses two things.

First, homeowners flush the chlorine out after an hour because they need the water back on, or they fill a lab bottle three days later while a faint trace of bleach is still hiding in the well—which buys a clean lab sheet on Friday, right before coliforms rebound two weeks later from the silt knocked loose during the pull.

That is why the one-month retest matters more than the first one. Second, almost nobody asks the installer what depth the new pump was hung at or where the static water level was sitting while the well was open. Have the pump model, horsepower, set depth, and static level written on your invoice before the truck hits the road. You cannot manage a well properly if you don't know where the pump is hanging.

Paperwork

The Province states that pump installation reports “do not need to be submitted to the ministry,” and the regulation requires no provincial filing for a straight pump swap. The Province does publish a standard Pump Installation Report form for installers to record the work—ask for a copy of what your installer wrote down.

If the well itself was altered during the visit—a change to its depth, diameter, or screen, a surface seal added where there was none, or hydrofracturing—the rules change. The person responsible must complete a well construction report, and for a water supply well, send copies to the Province and the well owner within 90 days after the alteration is finished (section 76).

If your well carries a provincial well identification plate, ensure that it is still attached with its number plainly visible once the crew clears out. Keeping it there is the owner’s duty, and a missing or damaged plate must be reported to the province with a request for a replacement within 30 days of finding it gone (section 56).

Your Duties Once the Installer Leaves

  • Cap: Keep the well cap securely attached and in good condition (section 39).
  • Drainage: Keep the ground around the wellhead graded so surface water cannot pond around the casing (section 58).
  • Storage: Nothing that counts as foreign matter may be left, stored, or allowed to build up within 3 metres of the wellhead of a water supply well (section 62).
  • Casing height: Where the regulation’s casing stick-up rule (section 33) applies to the well, keep the casing continuous and at least 0.3 metres above the ground, or above the floor of a well sump, pump house, or well pit (section 65).

Who Should Pay Attention

Private well owners who have just had a pump pulled, serviced, or replaced; rural buyers reviewing invoices for recent pump work during due diligence; and owners whose well supplies a second dwelling or suite.

What to Do Next

Ask your installer for the pump specs, set depth, and static water level in writing, confirm who handled the electrical permit, and check that the well cap and ID plate are tight before putting the tools away. Once the chlorine has been completely flushed from your lines, run a bacteriological test (total coliforms and E. coli) through an accredited lab at the one-week mark and again at the one-month mark, and boil your drinking water until the results come back clean.

Checked against: Groundwater Protection Regulation and Water Sustainability Act; Province of BC: Installing a Well Pump, Water Well Disinfection, and Well Reports; HealthLink BC: Drinking Water Chlorination Facts and Well Water Testing; Health Canada: Test Your Well Water; Technical Safety BC: Electrical Installation Permits · checked November 11, 2026

Related on the Wire: Power Is Back: What Should BC Well Owners Check Before Using Their Water?; What Should I Check About the Water Supply Before Buying a Rural Property in BC?

More Questions

All questions

Does a Water Softener Add Sodium to My BC Well Water?

If it runs on salt, yes. Health Canada says a softener that uses sodium may add undesirable amounts of it to the treated water, and recommends that the water you drink and cook with most, such as at the kitchen tap, bypass the softener.

Rural Property · Nov 19, 2026
Home